32PCS Car Paintless Dent Repair Puller Dint Hail Damage Lifter

About Golden Metal Dent Lifter:

-Aluminum body -Stainless Steel Adjustment knob

-Stainless Steel Nuts/Bolts/Pivot pin/E-Retaining clips O-ne screw on the top of the dent lifter is used to adjust the middle height of the dent lifter.

-With sandblasting oxidation process,the smooth texture feels and outstanding looks,The product is very strong and durable.

-On the bottom of the dent lifter is silicone,not ordinary rubber,which is very soft and not harmful for oil paint and can be torn down.

Note:

-Use adjustable lifting-mode movable tripod puller and adjust it against the size of the dent.

-During operation,you need to adjust your force gradually until the position where the dent is located is pulled to the flat and recovered entirely.

-The Dent Lifter squeeze trigger will allow you to control and massage door dings and hail damage until the desired results are achieved.

-New material and new design,stronger material.

About 20 W Mini Glue Gun:

Material: Plastic & Aluminum

Working power: 20 W

Working voltage: 100 to 220 V

Working temperature: 356 to 392

Nozzle diameter: 0.070-0.078 inch

Warm-up time: 3-5 minutes

Cable length: 55 inch

Size: 5.1 inch*4.3 inch*1 inch

Color: Blue

About Different Sizes Glue Puller Tabs

Features:

-Different tabs for different dent lifter or the Slide Hammer,Works with All Glue Pullers.

-Unique small pits design, fit for Auto Body Dent Repair,this special face can bond the glue well,also clean it easily,the size can match perfectly with dent puller/lifter.

-Durable design allows for perfect placement and superior adherent properties.

Hot Melt Glue Sticks

Features:

Softening Point: 178°F. (81°C.)

Working Time: 40 seconds

Viscosity / Centipoises: 5,500 @ 380°F. (193°C.) 12,000 @ 356°F. (180°C.)

Temperature of Glue Gun: High Temperature

Shape: Round

Warm Prompt:

-Keep clean of the glue sticks to avoid impurity block the nozzle,and do not pull out of the remanent glue sticks after each time using.

- To avoid get an electric shock during use,do not use it in a humid environment and keep it away from children.

-The remaining pressure inside the glue gun will push a little molten glue out of the gun even stop use,so to save your glue,please control release the trigger or cut off the power in advance.

- Cut off the power when stop using,and never try to disassemble the melt glue gun in any case.

How to use the Dent Puller:

-Clean dent surface,If the dent so small and can't see where is it,use a dent board to check where is the dent.

-Put the glue sticks to the gun and heat,connect the power source and preheat for 5-10 minutes.

-According to the dent size to choose the Glue Puller Tab,then put the heated glue on the puller tab,immediately place the puller tab in the center of the dent and hold on until it sticks.

-Let the glue cool for about 5-8 minutes.The cooling time should be less than 10 minutes and should be shorter slightly in winter.

-After the glue cooling,use a dent lifter or bridge puller to align and press the puller to pull up the dent.Repeat the above steps until the dent disappears.

-After finishing the dent,use the alcohol to clean the glue on the car and the puller tabs.

Package List:

1 * Golden Metal Dent Lifter

1 * Mini Glue Gun

18 * Glue Tabs

5 * Mini Yellow Glue Sticks

5 * Mini Black Glue Sticks

1 * Rubber Shovel

1 * Manual